Search

[nutjob]

My meiki plush doll arrived yesterday (and I'll have a lot of good things to say about it).....but I struggled with the insertion part of it.   I couldn't get my ZXY in more than about half way, even with the onahole wrap.   Maybe I was just being too gentle but it seemed to require quite a bit of effort.    So I tried my Story EXP, and while it's smaller size made it easier, it still seemed like work to get it in, and I never did get it inserted fully.   

I want to be clear that this isn't a negative with the meiki plush doll;  the doll is just genius and there's so much to love about it....just trying to understand the easiest way to insert the meiki.   

[DaaaBears]

hey nutjob, glad to hear you like the doll, i loved it personally.

As for inserting the ZXY, ya it's a little difficult. If you read my review, using the ona-wrap for the initial insertion, i still had to give it a few whacks and punches to get it in deeper. ZXY is a pretty fat sleeve so it definitely will take more punches. I suppose they can't make it too wide else smaller sleeves will simply fall out. Just punch and slap that zxy till it goes in, works for me!

[HardGay]

welcome to the meiki doll club haha..

I do the same thing Da Baaabears do...I insert about 2/3 of the way and the remaining part I have to give it a few slap our pound (in a safe manner that will not cause harm to these lovely babies). and it goes it well... the ZXY is a bit big and fat with the butt design...so that does not go in completely unless you force it and tie the string around it  

One thing I would add as a tip that i found out is that make sure to wrap the onawrap at the base of the toy ..if you wrap it like in mid section of the shaft of the toy..the silicone part that's sticking out in the base will still cause friction against the fabric which make it harder to insert.. have fun bro~  

do a review and let us know how you like it.

[tornomer]

What I found worked was to wrap the onahole in a paper towel or insert it into a clean dress sock before putting on the wrap then inserting. It covers up any of the material that is sticky from contacting the, what I assume, statin lining of the doll. Also, a clean damp wash cloth and air drying cleans up the doll pretty well. Only time will tell how much dirt will be left on the doll.

[casquetero]

I used the ona-hole wrap around the masturbator and then place a regular plastic shopping bag around it. The plastic of the shopping bag simply slides through the hole - although you will need to slap the XZY a few times to push it in its proper place. The string on the Meiki Plush doll helps to keep everything in place.

[HardGay]

I've tried the plastic bag or zip lock bags..those work very well sliding the sleeves into the cavity..but then it is also too easy for the toy to slip right back out because the lack of friction.
 

[xkingyox]

You could use a strip of saran wrap and wrap it around the toy with a little tail left at the front of the toy, then slip it in and slowly pull out the saran wrap from around the toy. That way it slides in, but after you pull the saran wrap out, it wont slide back out. I did this with my self made pillow doll and a strip of silky spandex.

[nutjob]

Good discussion.....

Happened across something in my house;  it looks kind of like a nylon bag to carry a small water bottle.   Most of it is mesh, except the closed end.   And it has a draw-string at the other end, with one of those black plastic clips that you squeeze to loosen the drawstring.   

One glance at it and I knew I had to try it, starting with my ZXY.   The meiki easily fit into this nylon thingie, and I was able to pull the drawstring closed pretty tightly.  The length was also good, because it came up just to where the ZXY starts to flare out in front.     The whole thing was MUCH, MUCH easier to slide into the meiki plush doll, and I finally got the ZXY fully inserted with minimal effort....   

In use, it worked beautifully.   The meiki stayed solidly in place even despite some, um, vigorous activity....and it was all very easily removed when I was done.   I didn't use the onahole wrap at all, because that would've been redundant.   

Unfortunately, I have NO idea exactly what this little nylon bag really is, so I doubt this helps anyone much.....but I'm thrilled with it.

[st4223]

What I found that worked really easier is to wrap a sock around the Meiki. Try that it's much easier than the plastic thingy that comes with the doll.

[demondabbler]

I've tried the plastic bag or zip lock bags..those work very well sliding the sleeves into the cavity..but then it is also too easy for the toy to slip right back out because the lack of friction.
 

If you really stuff it in there and then pull the drawstring, I have had no problem with the vagina falling out!

Imagine if this happened on a real woman? Ultimate brain trauma