Search

[VSpot]

So... I just added twelve pounds of Cap Barbell brand ankle weights to the legs and main cavity of my Meiki.  Gentlemen and Ladies... welcome to reality.  The Meiki plush doll is great as is but it is still light.  If you want that teddy bear maneuverability, do not change a thing about your Meiki.  Leave it alone.  Don't even read the rest of this post.  It doesn't pertain to you.  It only interferes with the perfection that you have already established.  Go put your favorite FL or Meiki into it, flip it over and go doggy nuts on it.  If you are looking for something more, something that you can arrange in five minutes, keep reading. 

The short story is this:  I cut two small slits into the inner wall of my Meiki and shoved in six 2 lb. ankle weights, one by one.  I easily shoved two in each leg and left two of them in the cavity but off to the side so that I could still fit an insert in.  Done.  Seriously.  Done.  It took just five minutes.

I loaded it up with an FL Stoya Destroya and played for a half an hour, using all of the usually suspected positions.  As usual, reverse cowgirl was the best position.  The difference this time was that you could let it ride you hands-free.  I couldn't help but to reach around and hold the breasts most of the time but at times, I just laid back with my hands and fingers together behind my head, with my blindfold mask on of course.  I always do this so I can pretend that I am with whoever I want to be with.  However, it felt so good that I made the unusual decision to watch her ride me in her Size S camisole.  Before finishing, I turned her around and thrusted her hips over me until I was almost ready to go.  At that point, I put my hands back behind my head again and let my hips and Meiki finish the job.  Seriously... I finished and she just sat up there.  If she had a face, she would have been grinning at me. 

Notes: 

I paid 25 dollars for the 20 lb weight set. 

I added 12lbs.  I will leave her like that for now.  For everyone else, I would say that 8lbs - 12lbs will work. 

I wiped the weight packs off first.  There was a little bit of lead dust.  No big deal. 

The missionary position was the "most improved." Normally, it is most stable when you put your weight onto it.  With it weighted, you could thrust in and out without even touching with it anything but your member. The cowgirl position is my all-time favorite and now it's just that much better. 

The FL case gives it that pubic bone feeling that you get when trim females are riding you.  I am not sore like usual but it added to the realism for me. 

If you try it and don't like it, just take the weights back to the store.  No harm done.  Just pretend it never happened.


I am not going to brag but this realism is important to me.  (I am used to Fleshlights.  I understand if you are loyal to Meiki.  That's fine.)  In the last twenty years, from my teen years until now, I have averaged five new women per year.  I like real women.  The stock, out-of-the-box Meiki Plush is the best masturbator on the market.  I take nothing away from it.  However, I have always been one who prefers to be ridden and the point of this plush is to imitate that so that I can spend less money on Cosmopolitans and maintain a solid G.P.A. on my way to earning my doctorate.  This doll is real enough.  And you know what?  The idea that it has no head almost adds to the feeling for me. 

If you want to try this modification, it is not a risk.  Unless losing $15-$25 could ruin you, I suggest to anyone to try this.  Have fun. 

VSpot

[HardGay]

Could you show us some picture of where the cut was? and would the weights fall out if your moving the doll too much while changing positions etc. 

Great mod btw!

[VSpot]

You know what... I can try but I actually don't think it matters.  I don't think the way I did it was that special.  However, it did work.  I made a 3 inch horizontal cut on the right side and a 3 inch vertical one on the left side.  I liked the horizontal cut better but like I said, I don't know if it mattered.  You just need to get the weights in and push them where you want them to go.  You can't really mess anything up in there!  In fact, I didn't even stitch closed the "incisions."  They are covered up by an insert!

PS -  No the weights can't fall out.  Not only are they shoved into the filling, the insert is blocking the holes.  This is fool-proof!

[HardGay]

oh, so you actually made the cut inside the sleeve insert area...i thought you meant making a cut on the thigh area of the doll.. my mistake.   thanks for the update.

[VSpot]

Yep, in the sleeve material.  This isn't even a low risk experiment, it's a NO RISK experiment.  And mine was successful!  I currently am set at 15.2 lbs.  Guess who doesn't hate the alarm clock as much these days?

[guhhyuk]

Sorry for resurrecting this thread but do you have a link to the ankle weights that you got? The only ones I've seen in that price range are the CAP ankle weights and the weights in those are iron filings and not solid bars.
https://www.amazon.com/CAP-Barbell-20-Pounds-Adjustable-Weights/dp/B0088ZVLAM/ref=sr_1_1?ie=UTF8&qid=1471508979&sr=8-1&keywords=cap+ankle+weights

will these provide enough support when inserted in the MPD legs?